Avenger 4x4
Latest News

Head for the Best EKO Canopy

The new EKO Canopy is coming.....

read more ...

Hitchgate by Wilco

Carry upto a 40' tyre in your hitch receiver, and remove it when its not needed.

read more ...

VW Amarok Workstyle Canopy

The NEW Avenger VW Amarok workstyle canopy.

read more ...

View News Archives...

Care Tips

Keeping your Avenger Top in good condition adds to your enjoyment and helps to maintain its value. The simple way to achieve this is to clean at regular intervals, those unsightly marks caused by the build up of traffic film and general grime.
Wash the surface first with a recognised detergent sold for use on fibreglass gelcoats. Should marks remain, use a cleaner with chemical and abrasive agents formulated for use on gelcoats.

DISCOLOURATION

Fading or discolouration of the gelcoat is a natural ageing process caused by ultraviolet light.
To overcome this, use a mild abrasive, which removes a thin layer of the discoloured surface.
This will restore the Avenger Top to its original colour and surface lustre.
Since discolouration develops gradually it should not be necessary to carry out this procedure more than once every three years. Frequent use of abrasive material can reduce the thickness of the gelcoat, to a potentially harmful extent. Depending on the severity of the discolouration.

REMOVING SCRATCHES FROM GELCOAT AND PAINTED SURFACES


Scratches can be removed from both gelcoat and painted surfaces. The method depends on the depth of the scratch, as care needs to be taken to avoid penetrating the paint or the gelcoat. Very fine hairline scratches can be removed by rubbing across the line of the scratch with rubbing compound. Slightly deeper scratches should be lightly wet sanded using very fine (1500 grit or finer) abrasive paper. Rubbing compound will then remove the flatting marks created by the abrasive paper. For deep gouge-type scratches where there is any danger of paint or gelcoat having been penetrated we recommend consulting a local bodyshop.

PROTECTING YOUR AVENGER CANOPY

Protecting gelcoats and painted surfaces against dirt, oil and extreme climatic conditions not only enhances the appearance of your Top but also prolongs its life, as well as helping maintain its original condition. A non-polymer, non-silicone wax polish is suitable for gelcoat surfaces, where as a silicone based polish is more suitable for painted surfaces. Both are easy to apply and causes no problem should any repairs be required.

 

LUBRICATE THE MOVING PARTS

All moving parts (excluding gas struts) should be lubricated with a multi-purpose oil every month. This will ensure the longevity of these parts and the continued enjoyment of your Top. The following should be lubricated:-

 

 

  •  Hinges - Use a penetrating oil on the pin such as 3-in-one. 
  •  Handle - Lubricate the lock and the mechanism.
  •  Rod Locks - Lubricate the center mechanism and apply grease to the ends.

DO NOT LUBRICATE THE GAS STRUTS. THEY ARE SELF LUBRICATING. SIMPLY REMOVE DIRT FROM THE SHAFT WITH A SOFT CLOTH. THIS WILL PROTECT THE PISTON SEALS.
STORAGE OF YOUR AVENGER TOP

STORAGE OF YOUR AVENGER CANOPY

When not in use, store your Avenger Top on a flat, level surface. Do not store on its side, roof or end. This may cause warping and cracking of the GRP. Avoid storing items on the roof.

UTE LINERS & CANOPIES
  
When installing a conopy on top of a ute liner you may experience some water leakage, this is caused by the textured top of the liner not sealing with the canopy correctly. It is recommended that an underlip liner is installed for the canopy to seal correctly on the top of the ute bed. If you allready have an overlip liner it is recommended to ask your installer to cut the top of the lip off so your Avenger Top
seals correctly.
 
 
 
SPARE PARTS
 
Avenger 4x4 Australia offer and stock a full range of spare parts for all our canopies, check back here soon for a full comprehensive parts list.

Shopping at Avenger 4x4 Accessories

Vehicles

Information

lighting,